|
22-24-centralnaya-konsol.html
22.24. The central consoleRemoval
|
|
Fig. 16–48. The central console: 1 – the left overlay of the central console; 2, 4, 6, 8, 18, 20, 21 – bolts, 2,5 Нм; 3 – the screw, 2,5 Нм; 5 – an ashtray; 7 – the central section of the panel of devices; 9 – a cap; 10 – tightening a bolt, 1 Нм; 11 – the handle of the lever of a lay brake; 12 – a washer; 13 – a decorative overlay; 14 – furnish of a lay brake; 15 – a back ventilating lattice; 16 – a decorative overlay of the panel of a back ventilating lattice; 17 – a bolt, 1,5 Нм; 19 – the central console
|
|
|
Fig. 16–49. The adaptation from a wire in diameter of 3 mm for dismantle of a ventilating lattice from the central section of the panel of devices: X = 6 mm
|
Make of a steel wire in diameter of 3 mm the adaptation for dismantle of a ventilating lattice from the central section of the panel of devices (fig. 16–49).
Remove the holder of phone.
Move forward seats against the stop back.
Turn an accelerator pedal on 90 counter-clockwise.
|
|
Fig. 16–50. An arrangement of bolts (1, 2) fastenings of the left furnish (3) central consoles
|
Unscrew bolts of 1 and 2 fastenings of the left upholstery of the central console (fig. 16–50).
Remove the left furnish from the central console for what move it forward and disconnect a back part of an upholstery.
|
|
Fig. 16–51. An arrangement of bolts (2, 3) fastenings of the right furnish (1) central consoles
|
Unscrew bolts of 2 and 3 fastenings of the right furnish of the central console (fig. 16–51). Access to forward bolts opens after removal of a carpet covering of a floor.
Remove the right furnish from the central console for what move it forward and disconnect a back part of an upholstery.
|
|
Fig. 16–52. An arrangement of a clamp (1) handles (2) levers of a lay brake
|
Lift, as far as possible, upwards the handle of a lay brake. Press downwards a clamp 1 (fig. 16–52) handles 2 levers of a lay brake and, having pulled, remove the handle from the lever.
|
|
Fig. 16–53. An arrangement of a cap (1) tightening bolts and a decorative overlay (2) upholsteries of the lever of a lay brake
|
Using a screw-driver edge as the lever, remove a decorative overlay 2 (fig. 16–53) from furnish of the lever of a lay brake.
Remove a cap, loosen the on two turns tightening a bolt and, moving forward, release a latch to a back part, remove furnish of the lever of a lay brake (fig. 16–53 see).
On cars with a mechanical transmission unscrew the handle from the lever of a gear change and include the fourth transfer.
Remove the central armrest.
|
|
Fig. 16–54. An arrangement of a back ventilating lattice (1), screws (3) and a decorative overlay (2)
|
Remove a decorative overlay of the panel of a back ventilating lattice (fig. 16–54).
Turn out two screws 3 and remove from a back part of the central console a ventilating lattice.
|
|
Fig. 16–55. Use of the adaptation from a wire (1), established in apertures (2) for removal of a ventilating lattice from the central section of the panel of devices
|
Fix the adaptation from a wire through a ventilating lattice in apertures of the case of a ventilating lattice of the central section of the panel of devices (fig. 16–55). Accurately take a ventilating lattice from the central section of the panel of devices.
|
|
Fig. 16–56. An arrangement of screws of fastening of the central section to the panel of devices
|
Unscrew five screws and take the central section from the panel of devices (fig. 16–56).
Disconnect electric sockets and remove the central section of the panel of devices.
|
|
Fig. 16–57. An arrangement of bolts (1) fastenings of the central console (2) and a bolt (4) fastenings of an ashtray (3)
|
Unscrew bolts 4 (fig. 16–57) and, moving forward, remove an ashtray 3 from the central console 2.
Unscrew bolts of 1 fastening of the central console; shifting and raising forward a back part of the console, remove it on the lever of a lay brake.
Installation
Installation is spent to sequences, return to removal.
|
|