Repair and service Audi A8 in body D2 with 1994 for 1999 of release.
1. Car operation
2. Maintenance service
3. Petrol engines of 2,8 l
4. Petrol engines of 3,7 and 4,2 l
5. Diesel engines of 2,5 l
6. Diesel engines of 3,3 l
7. Systems of ignition and injection of fuel of petrol engines
8. System of release of the fulfilled gases of cars with petrol engines
9. The power supply system of diesel engines
10. System of prestarting heating of diesel engines
11. System of release of the fulfilled gases of cars with diesel engines
12. Greasing system
13. Cooling system
14. Coupling
15. A transmission
16. Shaft of a drive of forward wheels
17. Features of a design of transmission of all-wheel drive cars
18. A suspension bracket
19. Wheels and tyres
20. A steering
21. Brake system
21.1. The general data
21.2. Antiblocking system of brakes (ABS)
21.3. Electronic system of stabilisation of course stability (ESP)
21.4. The general recommendations about operation and repair of antiblocking system of brakes and electronic system of stabilisation
21.5. Check of a rotor of gauge ABS
21.6. Replacement brake pads forward brake FN-3
21.7. Replacement brake pads forward brake HP-2
21.8. Replacement brake pads forward brake Brembo
21.9. Replacement back brake pads
21.10. Repair of forward support FN-3
21.11. Repair of forward support HP-2
21.12. Repair of forward support Brembo
21.13. Repair of a back support
21.14. A brake disk
21.15. The lever of a lay brake
21.16. Adjustment of a lay brake
21.17. Cables of a lay brake
21.18. Prorolling of a hydraulic drive of brakes
22. A body
23. Heating and air-conditioning system
24. An electric equipment
25. Electric schemes
 










21-17-trosy-stoyanochnogo-tormoza.html

21.17. Cables of a lay brake

Removal
Lift the car on the lift and remove back wheels.
Release a lay brake.
On all-wheel drive cars remove back section of system of release.

Fig. 15–38. An arrangement of bolts of fastening of a flange карданного a shaft to the main reverse gear and screws of fastening of a thermofilter



Note a flange relative positioning карданного a shaft and a flange of the main reverse gear and unscrew fastening bolts карданного a shaft to the main reverse gear (fig. 15–38).
Unscrew screws and remove the central thermofilter (fig. 15–38 see).

Fig. 15–34. Unscrewing of an adjusting nut of fastening of the jack and an arrangement of the springs fixing covers of cables of a lay brake



Special key 3343 weaken an adjusting nut of fastening of the jack on draught of the lever of a lay brake (fig. 15–34 see).
Remove cables of a lay brake from the jack.
Take out the springs fixing covers of cables of a lay brake (fig. 15–34 see).

Fig. 15–39. An arrangement of a bolt (1) fastenings of the shock-absorber and an arm (2) cables of a lay brake (3)



Disconnect a cable from a support (fig. 15–39).
Take a cover of a cable of a lay brake from an arm and move a cable to a back part (fig. 15–39 see).
Do not unscrew a bolt of fastening of the shock-absorber to the cross-section lever of a back suspension bracket (fig. 15–39 see).

Fig. 15–40. An arrangement of clamps (1, 4 and 5) and directing tubes (2, 3) fastenings of cables of a lay brake



Release the left cable of a lay brake from a clamp 1 (fig. 15–40) and, moving it back, take from a directing tube 2.
Release the right cable of a lay brake from clamps 4 and 5 and, moving it back, take from a directing tube 3.

Installation
Installation is spent to sequences, return to removal, taking into account the following.
Tighten fastening bolts карданного a shaft to the main reverse gear the moment 55 Н·м.
Check up, that the system has been established freely, without pressure, with a sufficient backlash from body elements.
Adjust a lay brake.


21.16. Adjustment of a lay brake

21.18. Prorolling of a hydraulic drive of brakes