Repair and service Audi A8 in body D2 with 1994 for 1999 of release.
1. Car operation
2. Maintenance service
3. Petrol engines of 2,8 l
4. Petrol engines of 3,7 and 4,2 l
5. Diesel engines of 2,5 l
6. Diesel engines of 3,3 l
7. Systems of ignition and injection of fuel of petrol engines
8. System of release of the fulfilled gases of cars with petrol engines
9. The power supply system of diesel engines
10. System of prestarting heating of diesel engines
11. System of release of the fulfilled gases of cars with diesel engines
12. Greasing system
13. Cooling system
14. Coupling
15. A transmission
16. Shaft of a drive of forward wheels
17. Features of a design of transmission of all-wheel drive cars
18. A suspension bracket
19. Wheels and tyres
20. A steering
21. Brake system
21.1. The general data
21.2. Antiblocking system of brakes (ABS)
21.3. Electronic system of stabilisation of course stability (ESP)
21.4. The general recommendations about operation and repair of antiblocking system of brakes and electronic system of stabilisation
21.5. Check of a rotor of gauge ABS
21.6. Replacement brake pads forward brake FN-3
21.7. Replacement brake pads forward brake HP-2
21.8. Replacement brake pads forward brake Brembo
21.9. Replacement back brake pads
21.10. Repair of forward support FN-3
21.11. Repair of forward support HP-2
21.12. Repair of forward support Brembo
21.13. Repair of a back support
21.14. A brake disk
21.15. The lever of a lay brake
21.16. Adjustment of a lay brake
21.17. Cables of a lay brake
21.18. Prorolling of a hydraulic drive of brakes
22. A body
23. Heating and air-conditioning system
24. An electric equipment
25. Electric schemes
 



Что записаться на эмс-тренировку Вы адреса и телефоны наших студий в минске: ул там.
Mc-3100 подробности здесь.
приватный чит на cs go купить - Trending videos.







21-14-tormoznojj-disk.html

21.14. A brake disk

Removal
Loosen the bolts of fastening of a wheel, lift a corresponding part of the car and fix on supports. Remove a wheel.
For reduction of losses of a brake liquid uncover a compensatory tank of brake system, close a mouth of a tank polyethylene and again screw a cover. It is necessary that the cover tightly closed a compensatory tank. It is possible to press also a clip the brake hose going to a support.
Unscrew bolts and remove the holder of a support together with a support from a rotary fist.
Clear a junction of a brake hose and the pipeline and unscrew a hose. Muffle apertures in a brake hose and the pipeline.
Disconnect a cable of a lay brake from a support of a back brake.
Remove a support.
Remove a brake disk.

Installation
Check up a condition and measure a thickness of a brake disk.
If replacement of a brake disk is necessary, it is necessary to replace both for maintenance of uniformity of braking. At replacement of brake disks it is necessary to replace and brake pads.
Check up and if necessary clear привалочные surfaces of a brake disk and a nave. At installation of a new brake disk remove from its surface a sheeting layer.
Establish a brake disk on a wheel nave.
Establish a support with brake колодками, without supposing перекручивания a brake hose. Be convinced that at turn of a forward wheel from one extreme position in another the brake hose does not adjoin to elements of a forward suspension bracket and a body.
Screw in a support bolts and tighten them.
If the brake hose was disconnected, connect it.
Remove polyethylene from a bulk mouth of a compensatory tank and pump over a corresponding brake contour.
Establish a wheel and lower the car on the earth.
Some times strongly press a brake pedal that brake pads have nestled on a brake disk.
Check up liquid level in a compensatory tank of brake system.


21.13. Repair of a back support

21.15. The lever of a lay brake