Repair and service Audi A8 in body D2 with 1994 for 1999 of release.
1. Car operation
2. Maintenance service
3. Petrol engines of 2,8 l
4. Petrol engines of 3,7 and 4,2 l
5. Diesel engines of 2,5 l
6. Diesel engines of 3,3 l
7. Systems of ignition and injection of fuel of petrol engines
8. System of release of the fulfilled gases of cars with petrol engines
9. The power supply system of diesel engines
10. System of prestarting heating of diesel engines
11. System of release of the fulfilled gases of cars with diesel engines
12. Greasing system
13. Cooling system
14. Coupling
15. A transmission
16. Shaft of a drive of forward wheels
17. Features of a design of transmission of all-wheel drive cars
18. A suspension bracket
18.1. A forward suspension bracket
18.2. An amortizatornaja rack
18.3. Dismantling and assemblage absorber racks
18.4. A rotary fist
18.5. The bottom forward frame
18.6. The forward stabilizer of cross-section stability
18.7. A back suspension bracket
18.8. The back shock-absorber
18.9. Shock-absorber check
18.10. The cross-section lever of a back suspension bracket
18.11. A back bottom frame
19. Wheels and tyres
20. A steering
21. Brake system
22. A body
23. Heating and air-conditioning system
24. An electric equipment
25. Electric schemes
 










18-11-zadnyaya-nizhnyaya-rama.html

18.11. A back bottom frame

Removal
The bottom back frame remove together with the main reverse gear, a rotary fist and levers of a back suspension bracket.
Using a screw-driver edge as the lever, remove a cap from the central part of a disk of a wheel.
On the car standing on wheels, loosen the bolts with a fillet of fastening of shaft of a drive to naves of back wheels.
Lift a back part of the car and fix on supports. Remove back wheels.
Remove back section of pipes of system of release of the fulfilled gases.
Remove a thermofilter of the back muffler.

Fig. 12–18. Use of special adaptation V.A.G 1752/1 for compression of springs of a back suspension bracket



By means of special adaptation V.A.G 1752/1 for compression of springs serially compress springs of a back suspension bracket and remove them (fig. 12–18 see). Spring coils should be grasped reliably the adaptation, a spring to compress from opposite sides.

The prevention
The spring has the big effort of compression, therefore use only very reliable tool.


Fig. 12–24. An arrangement of clips of a wire of gauge ABS



Release from clips and move towards a wire of gauges ABS (fig. 12–24).

Fig. 12–25. An arrangement of a bolt (1) fastenings of the shock-absorber to the cross-section lever and fastening of a cover (2) cables (3) lay brakes to an arm and a support



Disconnect a cable 3 lay brakes from a support of a back wheel (fig. 12–25).
Take a cover 2 cables of a lay brake from an arm, with effort having moved a cable from a support.
Unscrew a bolt of 1 fastening of the shock-absorber to the cross-section lever.

Fig. 12–26. A bolt arrangement (the second bolt is not visible) fastenings of a support of a back brake



Unscrew bolts of fastening of a back support (fig. 12–26). A soft wire, adhere a support to a body. The support should not hang on a brake hose.

Fig. 12–27. An arrangement of labels of combination and fastening bolts карданного a shaft to a flange of the main reverse gear



Check up, whether there are combination labels on a flange карданного a shaft and a flange of the main reverse gear (fig. 12–27). In the absence of labels put them.

Fig. 12–28. Use of a wooden wedge (1) for поджатия карданного a shaft upwards to a thermofilter (2)



Wooden wedge draw in propeller a shaft upwards to a thermofilter (fig. 12–28).
Unscrew bolts and remove a thermofilter located over карданным shaft.
Unscrew bolts of fastening of a flange карданного a shaft to a flange of the main reverse gear.
Release cables of a lay brake from holders and, moving them to a back part of the car, take from the directing.
Unscrew a bolt and separate directing a cable of a lay brake.
Establish under the main reverse gear a jack with adaptation V.A.G 1359/2 and raise a jack so that the weight of a back bottom frame with the main reverse gear was perceived by a jack.

Fig. 12–29. An arrangement of bolts of fastening of the bottom back frame.



Unscrew bolts of fastening of the bottom back frame (fig. 12–29), lower a jack and remove the bottom frame with the main reverse gear.

Installation
Installation is spent to sequences, return to removal, taking into account the following.
At installation of the bottom frame check up, that hoses of ventilation of a fuel tank have not been pressed.
Screw in and tighten new bolts of fastening of the bottom frame the moment 150 Нм and then tighten them on a corner 90 .
Establish into place and fix cables of a lay brake.
Establish a thermofilter over карданным shaft.
In a flange of the main reverse gear clear a carving for bolts of fastening of a cranked shaft.
At installation карданного a shaft for a disbalance exception combine labels on a flange карданного a shaft with labels on a flange of the main reverse gear (fig. 12–27 see).
Check up, that details of system of release have been located freely and bodies did not concern.


18.10. The cross-section lever of a back suspension bracket

19. Wheels and tyres