|
6-3-perednyaya-poperechina-motornogo-otseka.html
6.3. A forward cross-beam of a motor compartmentRemoval
Before a detachment of the storage battery find out, whether there is at you a code of inclusion of a radio receiver.
Switch off ignition and disconnect a wire of "weight" from the storage battery.
Uncover a broad tank.
Remove forward wheels.
|
|
Fig. 3.4–15. An arrangement of screws of fastening of a heater of an exhaust pipe and a noise isolation of an additional heater
|
Turn away screws of fastening of a heater of an exhaust pipe and a noise isolation of an additional heater (fig. 3.4–15).
|
|
Fig. 3.4–16. An arrangement of clamps of fastening of the bottom mudguard of a motor compartment
|
Release clamps and remove forward section of the bottom mudguard of a motor compartment (fig. 3.4–16).
Establish under the engine the pallet for liquid gathering.
|
|
Fig. 3.4–17. An arrangement of carving stoppers for plum of a cooling liquid from cooling system
|
Unscrew three carving stoppers and merge cooling liquid from cooling system (fig. 3.4–17).
Release a clip, loosen the a collar and remove hoses of system of cooling in a forward part of a motor compartment.
Unscrew a bolt and disconnect from the bottom part of a radiator the pipeline of cooling of an automatic transmission.
Disconnect an electric socket from electromagnetic муфты, release a clamp and move wires aside.
Remove a forward casing.
|
|
Fig. 3.4–18. Clearing of clamps of fastening of a lattice of an air inlet
|
Screw-driver with a thin edge release clamps and remove lattices of an air inlet from a bumper (fig. 3.4–18).
On cars with screen wipers of headlights disconnect a hose of a washer from the T-shaped connector.
Through opened apertures unscrew bolts from two parties of a bumper and remove a bumper.
Release clips and separate from a forward cross-beam an air inlet and its branch pipe.
|
|
Fig. 3.4–19. Removal of a casing of the engine
|
Having pulled for lateral faces upwards, remove an engine casing (fig. 3.4–19).
Turn away screws and remove an additional left casing in a motor compartment.
Merge a liquid from hydraulic system of the amplifier of the helmsman at board.
Loosen the collars, turn out connecting nuts and disconnect tubes of hydraulic system of the amplifier of a steering.
Release from clips a cable of opening of a cowl.
Unscrew a bolt and disconnect from the top part of a radiator the pipeline of cooling of an automatic transmission.
Loosen the collars also remove hoses of system of cooling from a forward cross-beam.
Disconnect a hose of system of cooling from the right top part of a radiator.
Disconnect electric sockets from the left and right headlights.
|
|
Fig. 3.4–20. An arrangement of the screw of fastening of a headlight
|
Turn out on one screw and remove headlights (fig. 3.4–20).
|
|
Fig. 3.4–21. An arrangement of electric sockets about a sound signal
|
Disconnect the electric sockets located about a sound signal (fig. 3.4–21).
Remove air inlets at the left and to the right of a radiator.
Turn out screws and remove a radiator of hydraulic system of the amplifier of a steering.
Remove the bottom air inlet of a radiator.
|
|
Fig. 3.4–22. An arrangement of bolts of fastening of an arm of a bumper
|
|
|
Fig. 3.4–23. An arrangement of a bolt of fastening of a forward cross-beam
|
Unscrew bolts, which through rubber plugs крепят a forward cross-beam (fig. 3.4–23).
Remove a forward cross-beam with the assistant.
Installation
The engine establish in sequence, return to removal, taking into account the following.
Establish a forward cross-beam.
Establish headlights.
Check up and if necessary adjust light of headlights.
|