Repair and service Audi A8 in body D2 with 1994 for 1999 of release.
1. Car operation
2. Maintenance service
3. Petrol engines of 2,8 l
4. Petrol engines of 3,7 and 4,2 l
5. Diesel engines of 2,5 l
6. Diesel engines of 3,3 l
7. Systems of ignition and injection of fuel of petrol engines
8. System of release of the fulfilled gases of cars with petrol engines
9. The power supply system of diesel engines
10. System of prestarting heating of diesel engines
11. System of release of the fulfilled gases of cars with diesel engines
12. Greasing system
13. Cooling system
14. Coupling
15. A transmission
16. Shaft of a drive of forward wheels
17. Features of a design of transmission of all-wheel drive cars
17.1. The general data
17.2. A kardannyj shaft
17.3. Position adjustment карданного a shaft
17.4. The main reverse gear
17.5. Back shaft of a drive
17.6. Differential of the main reverse gear
18. A suspension bracket
19. Wheels and tyres
20. A steering
21. Brake system
22. A body
23. Heating and air-conditioning system
24. An electric equipment
25. Electric schemes
 



ChillOut: ƒубай „илаут слушать - PsyChill







17-3-regulirovka-polozheniya-kardannogo-vala.html

17.3. Position adjustment карданного a shaft

Adjustment of position of an intermediate support карданного a shaft.
At presence, unscrew four bolts and remove the cross-section beam located under pipes of system of release.
Unscrew nuts, крепящие connecting clips of exhaust pipes, disconnect and remove back section of system of release.
Unscrew bolts and remove a thermofilter located over карданным shaft.

Fig. 11–2. An arrangement of bolts of fastening of the tunnel карданного a shaft



Unscrew bolts and remove the tunnel (fig. 11–2 see).
Establish and fix on карданном to a shaft the adaptation 3139.
Unscrew bolts and remove washers of fastening of an intermediate support карданного a shaft.


Fig. 11–4. Installation of an intermediate support карданного a shaft

Distance (), the           Thickness
                        Lining mm                     , mm
  0–3,0                              
                             3,1-5,0 2
                             5,1-7,0 4
                             7,1-9,0 6
                           9,1-11,0 8
                        11,1-13,0 10

Establish an intermediate support карданного a shaft so that distance D (fig. 11–4) from a support to a body and was identical from two parties. Measure this distance and depending on distance size choose a thickness of adjusting linings:

Adjustment of axial position карданного a shaft
Using the adaptation 3139, move as far as possible propeller a shaft to the main reverse gear.

Fig. 11–5. An arrangement of the centre of an aperture for bolts of fastening of an intermediate support карданного a shaft at various positions карданного a shaft


In this position note position of the centre of an aperture for bolts of fastening of an intermediate support карданного a shaft (the marksman And, fig. 11–5).
Using the adaptation 3139, move as far as possible propeller a shaft to a transmission.
In this position карданного a shaft repeatedly note position of the centre of an aperture for bolts of fastening of an intermediate support карданного a shaft (the arrow In, see fig. 11–5).
Move propeller a shaft along an axis to such position at which apertures for bolts of fastening of an intermediate support карданного a shaft will be in the middle before the made marks (the marksman With, fig. 11–5) see.
Establish adjusting linings of the chosen thickness and fix bolts an intermediate support карданного a shaft.
Remove the adaptation 3139 with карданного a shaft.
Establish the tunnel карданного a shaft.
Establish over карданным shaft a thermofilter.
Check up, that the release system has been located freely and did not concern bodies.


17.2. A kardannyj shaft

17.4. The main reverse gear