|
7-7-tros-akseleratora.html
7.7. An accelerator cableRemoval
Remove the bottom casing of the panel from outside the driver.
Take in deepening for feet of the driver transitive заглушку from a partition of a motor compartment.
|
|
Fig. 4.1–15. Removal of a cable (1) accelerators from the top part of a pedal (2) accelerators
|
Disconnect a cable of an accelerator from the top part of a pedal of an accelerator (fig. 4.1–15)
Cars with an automatic transmission
Disconnect an electric socket from the mechanism of compulsory inclusion of a hill-climbing gear.
Remove the protective casings located in the left back part of a motor compartment.
|
|
Fig. 4.1–16. An arrangement of screws of fastening of a casing of the six-cylinder engine
|
|
|
Fig. 4.1–17. An arrangement of screws of fastening of a casing of the eight-cylinder engine
|
Cars with the cruise-control
|
|
Fig. 4.1–18. An arrangement of a vacuum hose (2) and bolts (1) fastenings of the vacuum chamber of system of the cruise-control
|
Disconnect a vacuum hose 2 from the vacuum chamber of system of the cruise-control (fig. 4.1–18).
Unscrew two bolts and remove from an arm the vacuum chamber of system of the cruise-control.
Cars with six-cylinder engines
|
|
Fig. 4.1–19. Fastening of a cable of an accelerator to the lever of a drive throttle заслонки cars with six-cylinder engines: 1 – a tip of a cable of an accelerator; 2 – an arm; 3 – a spring clip; 4 – the rubber plug of a cover of a cable of an accelerator; 5 – a spring clamp
|
Using рожковый a key on 8 mm, disconnect a tip of a cable of 1 accelerator from the lever of a drive throttle заслонки (fig. 4.1–19).
Take a spring clip of 3 fastenings of a cover of a cable of an accelerator to an arm 2 and take a cable from an arm 2.
Using a screw-driver edge as the lever, remove a spring clamp 5.
Cars with eight-cylinder engines
|
|
Fig. 4.1–20. Fastening of a tip of a cable of an accelerator (1) to the lever (2) drives throttle заслонки
|
Disconnect a tip of a cable of an accelerator from the lever of a drive throttle заслонки (fig. 4.1–20).
|
|
Fig. 4.1–21. Fastening of a cable of an accelerator on cars with six-cylinder engines: 1 – the rubber plug; 2 – a spring clip; 3 – an arm; 4 – a cover of a cable of an accelerator
|
Take out a spring clip 2 (fig. 4.1–21) and the rubber plug 1 with a cover of a cable 4 accelerators from an arm 3.
|
|
Fig. 4.1–22. The air filter: 1 – an air line; 2 – a measuring instrument of the expense of air G70; 3 – a collar; 4 – an inlet air line; 5 – a collar; 6 – a soaking up air line; 7 – a nut; 8 – a rubber pillow; 9 – a filtering element of the air filter; 10 – the case of the air filter; 11, 12 – an air line
|
|
|
Fig. 4.1–23. A fuel highway with atomizers: 1 – a tube of a supply of fuel from the fuel filter; 2 – a tube of return of fuel; 3 – a bolt, 10 Нм; 4 – a spring connector; 5 – sealing rings; 6 – a regulator of pressure of fuel; 7 – a fuel highway; 8 – a spring connector; 9 – a sealing ring; 10 – an atomizer; 11 – a sealing ring; 12 – an inlet collector
|
|
|
Fig. 4.1–24. Throttle knot and system of switching of an inlet collector: 1 – the top part of an inlet collector; 2 – a bolt, 10 Нм; 3 – a bolt, 20 Нм; 4 – a lining; 5 – the valve of stabilisation of idling N71; 6 – a bolt, 10 Нм; 7 – a bolt, 6 Нм; 8 – a flange; 9 – the basis of an inlet collector; 10 – a lining; 11 – a bolt, 10 Нм; 12 – the vacuum chamber of the valve of switching of an inlet collector; 13 – a bolt, 20 Нм; 14 – throttle knot; 15 – a lining; 16 – a bolt, 20 Нм; 17 – the mechanical valve of system рециркуляции the fulfilled gases (EGR); 18 – the gauge of temperature EGR G98; 19 – a bolt, 10 Нм; 20 – a lining; 21 – a bolt, 10 Нм
|
Installation
Installation is spent to sequences, return to removal.
Do not suppose excesses of a cable of an accelerator.
Adjust an accelerator cable.
Adjustment of a cable of an accelerator
The help of the second mechanic is necessary for adjustment of position of a cable of an accelerator.
Take out a spring clip and the rubber plug with a cover of a cable of an accelerator from an arm.
Press an accelerator pedal against the stop and adjust position of a cable of an accelerator so that throttle заслонка it was completely open. Position of a cable of an accelerator is regulated by moving of the rubber plug on a cable cover. In this position insert the rubber plug of a cover and fix its spring clip.
The note
At installation it is necessary to use new sealing rings and linings.
|