Repair and service Audi A8 in body D2 with 1994 for 1999 of release.
1. Car operation
2. Maintenance service
3. Petrol engines of 2,8 l
4. Petrol engines of 3,7 and 4,2 l
5. Diesel engines of 2,5 l
6. Diesel engines of 3,3 l
7. Systems of ignition and injection of fuel of petrol engines
8. System of release of the fulfilled gases of cars with petrol engines
9. The power supply system of diesel engines
10. System of prestarting heating of diesel engines
11. System of release of the fulfilled gases of cars with diesel engines
12. Greasing system
13. Cooling system
14. Coupling
15. A transmission
16. Shaft of a drive of forward wheels
16.1. The general data
16.2. Removal and installation of a shaft of a drive
16.3. Removal and installation of the external hinge of a shaft of a drive
16.4. A holder of the hinge of a shaft of a drive
17. Features of a design of transmission of all-wheel drive cars
18. A suspension bracket
19. Wheels and tyres
20. A steering
21. Brake system
22. A body
23. Heating and air-conditioning system
24. An electric equipment
25. Electric schemes
 










16-4-obojjma-sharnira-vala-privoda.html

16.4. A holder of the hinge of a shaft of a drive

Removal
Remove from the SHRUS end face a lock ring and a face cover.
Remove from a drive shaft an internal SHRUS for what screw in in a shaft an old bolt, establish a holder of a shaft of a drive on tubular the mandrel and, striking on a bolt a plastic hammer, press on the hinge case on a drive shaft, thus hold a drive shaft at an angle nearby 20 °.
Remove collars of fastening of a protective cover of the hinge and shift a cover on a drive shaft.

Fig. 10–8. A label defining mutual position of the case of the hinge (1), holders (2) and a shaft of a drive (3)



Waterproof marker note mutual position of the case of the hinge, a holder and a drive shaft (fig. 10–8 see).
Remove a sealing ring from an end face of the case of the hinge.

Fig. 10–9. Removal of a lock ring of fastening of a holder of the hinge to a drive shaft



Remove a lock ring, крепящее a hinge holder to a drive shaft (fig. 10–9).
Using a stripper, remove a holder of the hinge from a drive shaft.
Remove the case of the hinge from a drive shaft.
Carefully clear a shaft and the case of the hinge of greasing.
Check up a condition of a holder of the hinge, rollers and the hinge case.

Installation
Put on a drive shaft a small collar of fastening of a protective cover and a protective cover.
Establish on a shaft the hinge case.
Establish on a shaft of a drive a holder with rollers and fix its lock ring.
Put 70 г greasings G 000 605 on a hinge holder from outside a shaft of a drive and establish into place the hinge case.
Put 70 г greasings G 000 605 on the other hand holders.

Fig. 10–10. An arrangement of a lock ring (1) covers (2) and a sealing ring (3) in an end face of a holder of the hinge of a shaft of a drive



Establish at an end face of the case of the hinge a sealing ring, a cover and a lock ring (fig. 10–10).
Establish on the hinge a protective cover and fix its collars, preliminary having raised a screw-driver internal edge of a cover for alignment of pressure of air under a cover.

Fig. 10–7. Application of the special tool for collar fastening: And – the screw for an inhaling of sponges of the tool; In – installation of sponges of the tool on a collar



For fastening of collars it is necessary to use the tool 1683 (fig. 10–7 see). Tool sponges establish on corners of a clip of a collar and in this position compress sponges the screw, having tightened its moment 20 Н·м.


16.3. Removal and installation of the external hinge of a shaft of a drive

17. Features of a design of transmission of all-wheel drive cars