Repair and service Audi A8 in body D2 with 1994 for 1999 of release.
1. Car operation
2. Maintenance service
3. Petrol engines of 2,8 l
4. Petrol engines of 3,7 and 4,2 l
5. Diesel engines of 2,5 l
6. Diesel engines of 3,3 l
7. Systems of ignition and injection of fuel of petrol engines
8. System of release of the fulfilled gases of cars with petrol engines
9. The power supply system of diesel engines
10. System of prestarting heating of diesel engines
11. System of release of the fulfilled gases of cars with diesel engines
12. Greasing system
13. Cooling system
14. Coupling
15. A transmission
16. Shaft of a drive of forward wheels
17. Features of a design of transmission of all-wheel drive cars
17.1. The general data
17.2. A kardannyj shaft
17.3. Position adjustment карданного a shaft
17.4. The main reverse gear
17.5. Back shaft of a drive
17.6. Differential of the main reverse gear
18. A suspension bracket
19. Wheels and tyres
20. A steering
21. Brake system
22. A body
23. Heating and air-conditioning system
24. An electric equipment
25. Electric schemes
 



Здесь пектолит.







17-4-glavnaya-zadnyaya-peredacha.html

17.4. The main reverse gear

Removal
At presence unscrew four bolts and remove the cross-section beam located under pipes of system of release.
Unscrew nuts, крепящие connecting clips of exhaust pipes. Disconnect and remove back section of system of release.

Fig. 11–3. An arrangement of labels of combination and fastening bolts карданного a shaft to a flange of the main reverse gear



Check up, whether there are labels on карданном to a shaft and a flange of the main reverse gear for their combination (fig. 11–3 see). In the absence of labels put them.
Loosen the bolts of fastening of flanges карданного a shaft to flanges of a transmission and the main reverse gear (fig. 11–3 see).

Fig. 11–6. Use of a wooden wedge (1) for поджатия карданного a shaft upwards to a thermofilter (2)



Wooden wedge draw in propeller a shaft upwards to a thermofilter (fig. 11–6).
Unscrew bolts and remove a thermofilter located over карданным shaft.
Unscrew bolts of fastening of a flange карданного a shaft to a flange of the main reverse gear.
At presence release a clamp of fastening of a cable of a lay brake.
Remove a thermofilter of the left shaft.
Unscrew bolts of fastening of internal SHRUS of back shaft of a drive to flanges of the main reverse gear.
Establish under the main reverse gear a jack with adaptation V.A.G 1359/2.

Fig. 11–7. An arrangement of bolts of fastening of the left support of the main reverse gear



Unscrew bolts of fastening of the left support of the main reverse gear (fig. 11–7).

Fig. 11–8. An arrangement of bolts (1, 2, 4) fastenings of the main reverse gear to a cross-section back beam (3)


Unscrew bolts of fastening 1 and 2 main reverse gears to a cross-section back beam 3 (fig. 11–8).
Being careful, lower the main reverse gear and take it from below the car.

Installation
Installation is spent to sequences, return to removal, taking into account the following.
In a flange of a transmission and the main reverse gear clear a carving for fastening bolts карданного a shaft.
Check up, that on flanges карданного a shaft there was no greasing. Remove from sealing linings a protective film and establish linings on flanges the sticky party to карданному to a shaft.
Lift the main reverse gear so that it was possible to attach back shaft of a drive to flanges of the main reverse gear. Screw in, but do not tighten completely bolts of fastening of shaft of a drive to flanges of the main reverse gear.
Lift the main reverse gear, establish into place and fix bolts 1 and 2 on a cross-section back beam (fig. 11–8 see).
At installation карданного a shaft for a disbalance exception combine labels on a flange карданного a shaft with labels on flanges of a transmission and the main reverse gear (fig. 11–3 see).
Screw in fastening bolts карданного a shaft to flanges of the main reverse gear.
Tighten bolts of fastening of shaft of a drive to flanges of the main reverse gear.
Check up oil level in the main reverse gear.
Check up, that the release system has been located freely and did not concern bodies.


17.3. Position adjustment карданного a shaft

17.5. Back shaft of a drive